Research on the Internal Power Gear Honing Processing Technology for Hard Tooth Surface

Author(s): 
Y. Gao†‡*, J. Han†, L. H. Li‡, L. Liu§, & F. G. Lv††

Affiliation(s): 
Institute of CIMS, Hefei University of Technology, Hefei, 230009, China
‡College of Mechatronic Engineering, Beifang University of Nationalities, Yinchuan, 750021, China
§Department of Mechanical Engineering, University of Kansas, Lawrence, 66045, China
††Nan Jing No.2 Machine Tool Works, Nanjing, 211103, China

Cite this paper
Y. Gao†‡*, J. Han†, L. H. Li‡, L. Liu§, & F. G. Lv††, “Research on the Internal Power Gear Honing Processing Technology for Hard Tooth Surface”, Journal of Mechanical Engineering Research and Developments, vol. 39, no. 2, pp. 500-512, 2016. DOI: 10.7508/jmerd.2016.02.029

ABSTRACT: Internal meshing force is in traditional gear honing gear honing processing technology developed on the basis of a kind of high quality hard tooth surface gear finishing method. It besides has advantages of traditional internal gear honing, not only shorten gear finishing technological process, improve production efficiency, reduce the cost of finishing and powerful after gear honing workpiece with better wear properties, lower noise and longer service life of transmission. Based on the analysis of internal meshing gear honing technology development process, the processing principle, processing characteristics, processing technology and technical status quo, on the basis of in-depth study the method of strong gear honing processing technology characteristics and processing technology research status quo, honing wheel manufacturing technology and strong gear honing machine tool technology. Finally, strongly internal meshing gear honing mechanism and process of powerful gear honing method of ultrasonic vibration, smart gear manufacturing equipment and the plover wheel manufacturing technology is discussed, in order to promote the development of strong gear honing technology.

Keywords : Hard tooth surface gear; Strong internal gear honing; Processing technology.

References

[1] B. Karpuschewski, H. J. Knoche, M. Hipke, “Gear finishing by abrasive processes”, CIRP Annals – Manufacturing Technology, vol. 57, no. 4, pp. 621-640, April 2008.
[2] N. Amini, B.G. Rosrn, and H. Westberg, “Optimization of Gear Tooth Surfaces”, Int. J. Mach. Tools Manufact, vol. 38, no. 6, pp. 425-435, June 1998.
[3] F. Klocke, V. Vasiliou, “Analysis of the influence of gear dimensions on cutting speedand contact conditions during the gear honing process”, Prod. Eng. Res. Devel, vol. 19, no. 3, pp. 255-259, March 2009.
[4] M. Lv, G. X. Liang, “The Progress and Prospects of Hardened Tooth Surface Gear Processing Technology”, Journal of Taiyuan University of Technology, vol. 9, no. 3, pp. 237-242, March 2012.
[5] G. Yang, H. Jiang, L. Lin, “Research on the Tooth-Surface Controlling and Honing Machining of the Ultral-Precision CBN Gear”, The Open Mechanical Engineering Journal, vol. 9, no. 1, pp. 831-836, October 2015.
[6] K. D. BOUZAKIS, N. MICHAILIDIS, “Manufacturing of cylindrical gears by generating cuttingprocesses: A critical synthesis of analysis methods”, CIRPAnnals – Manufacturing Technology, vol. 57, no. 2, pp. 676-696, February 2008.
[7] C. T. Tang, T. Y. Tang, “Process of Automobile Gear Machining Technology”, Practical Electronics, vol. 16, no. 7, pp. 253-254, July 2013.
[8] L. D. Wang, S. Y. Ling, “Processing methods of precision and ultra-precision cylindrical involute gear, “Optics and Precision Engineering, vol. 17, no. 2, pp. 321-326, February 2009.
[9] G. Liu, K. Y. Lee, and H. F. Jordan, “TDM and TWDM de Bruijn networks and shufflenets for optical communications”, IEEE Trans. Comp., vol. 46, no. 4, pp. 695-701, June 1997.
[10] B.Karpuschewski, H. J. Knoche, M. Hipke, “Gear finishing by abrasive process”, CIRP Annals-Manufacturing Technology, vol. 57, no. 5, pp. 620-640, May 2008.
[11] F. Klocke, C. Gorgels, V. Vasiliou, “Analysis of the influence of gear dimensions on cutting speedand contact conditions during the gear honing process”, German Academic Society for Production Engineering, vol. 7, no. 3, pp. 255-259, March 2009.
[12] G. S. Ruan, L. Q. Shen, “Research and application of the internal gear honing process”, Manufacturing Technology & Machine Tool, vol. 5, no. 12, pp. 29-32,  December 1990.
[13] N. Amini, H. Westberg, F. Klocke and T. Kollner, “An Experimental Study on theEffect of Power Honing onGear Surface Topography”, Gear Technology, vol. 2, no. 1, pp. 11-18, January 1999.
[14] Z. G. Guo, “New gear honing process”, Aviation Maintenance & Engineering, vol. 5, no. 9, pp. 18-20, September 1989.
[15] E. Bergseth, “Influence of real surface topography on the contact area ratio in differently manufactured spur gears”, Tribology International, vol. 56, no. 1, pp. 72-80, January 2012.
[16] Litvin, F. L, Gear Geometry and AppliedTheory. PTRPrentice Hall,1994.
[17] X. T. Wu, Gear Engagement Theory. China Machine Press,1982.
[18] D. A. Zhan, X. T. Wu, “Theoretical Study On Internal Gear Honing and Analysis of Computer Simulating Gear Tooth Contact”, Tool Engineering, vol. 31, no. 1, pp. 9-11, January 1997.
[19] T. Y. Li, “Theory Analysis and Experiment of Continuous HoningWith a Honing Ring”, Journal of Mechanical Transmission, vol. 1, no. 11, pp. 35-40, November 1990.
[20] M. Lv, G. X. Liang, “Influence of Distribution Characteristics of Gear Honing Speed at the Contact-points on the Surface Quality of Gear Teeth”, China Mechanical Engineering, vol. 22, no. 15, pp. 1867-1871, August 2011.
[21] M. Q. Luo, “Theoretical Study on Plane Internal Gear Honing”, Journal of Shanghai Electric Technology, vol. 11, no. 2, pp. 1-4, February 2008.
[22] S. Y. Zhao, “Simulation Machining Analysis for Internal Gear Honing based on UG”, Journal of Mechanical Transmission, vol. 37, no. 2, pp. 97-99, February 2013.
[23] T. Yu, S. Y. Wang, “Theory Analysis and Experiment of Continuous Honing With a Honing Ring”, Machine Design and Research, vol. 20, no. 4, pp. 66-68, April 2004.
[24] Z. G. Guo, “Internal gear honing”, Machinery, vol. 3, no. 9, pp.6-8, September 1987.
[25] S. P. D. Santos, L. C. Brandao, “Finishing process analysis between honing and hard hobbingin pinion gears applied to a steering system, in Second International Conference in Energy Engineering, Energy Procedia, 2012, pp. 2-8.
[26] C. Marzenell, H. K. Tonshoff, “Properties of Tooth Surfaces due to Gear Honing with Electroplated Tools”, in 4th Word Congresson Gearing and Power Transmission, 1999, pp. 1711-1724.
[27] H. K. Tonshoff, T. Friemuth, C. Marzenell, “Properties of Honed Gears During Lifetime”, Annals of the ClRP, vol. 49, no. 7, pp. 431-434, July 2000.
[28] C. L. Wang, Y. Liu, L. Chen, “Study on CBNhoning wheel mechanism of tooth correction”, Journal of Mechanical Transmission, vol. 26, no. 3, pp. 20-23, March 2002.
[29] Y. M. Shen, Y. M. Han, “Gear honing process and production honing wheel”, CFHI Technology, vol. 4, no. 3, pp. 34-35, March 2004.
[30] H. GUNBARA, “A Study on Gear Honing Using Grinding Wheel Shaped in Internal Gear”Journal of Mechanical Transmission, vol. 27, no. 3, pp. 721-726, March 2003.
[31] Y. F. Li, M. D. Zhang, “Dynamic simulation analysis of plated CBN hard gear-honing processing based on LS-DYNA”, Journal of Graphics, vol. 33, no. 3, pp. 110-113, March 2012.
[32] T. Yu, D. X. Yang, Q. F. Tian, “A New Method of Profiling honing Gear”, Machine Tool & Hydraulics, vol. 6, no. 5, pp. 25-26, May 2002.
[33] Z. W. Wang, “Technology of 3D Modeling for Honer and the Kinematic Simulation of Honing Mechanism Based on Pro/Engineer”, Mechanical Engineering & Automation, vol. 5, no. 1, pp. 83-85, January 2006.